Differences

This shows you the differences between two versions of the page.

--- phones:docomo:motorola [2025/08/08 05:40] – lnrc
+++ phones:docomo:motorola [2025/08/13 23:58] (current) – lnrc
@@ Line 7: / Line 7: @@
 ===== Introduction =====
-Motorola only released a few phones for Docomo. Most are compatible with tools used to extract data from other Motorola phones that were released internationally.
+Motorola only released a few phones for Docomo. These devices are compatible with tools used to extract data from other Motorola phones released internationally.
 ^ Phone Model ^ Extractable? ^ File System (Main Storage) ^ FTL (Flash Translation Layer) ^ Tools ^
 | M702iG | Yes | Primary: Intel FHS (CG2)\\ Secondary: FAT16 (CG1) | Primary: None\\ Secondary: FlashFX 4.00 | [[#Flash Terminal]] |
 | M702iS | Yes | Primary: Intel FHS (CG2)\\ Secondary: FAT16 (CG1) | Primary: None\\ Secondary: FlashFX 4.00 | [[#Flash Terminal]] |
-| M1000 | No | Unknown | Unknown | [[#Flash Terminal]] |
+| M1000 | No | Unknown | Unknown | [[#FlashTerminal]] |
 ===== Methods =====
 Extracting Data
-  -  [[https://github.com/EXL/FlashTerminal|Flash Terminal]]
+  - [[https://github.com/EXL/FlashTerminal|FlashTerminal]]
-==== Flash Terminal ====
+You can find instructions for preparing your Motorola phone and using Flash Terminal [[https://lpcwiki.miraheze.org/wiki/Dumping_firmware_from_phones/Motorola|here]]
-WIP
+Reading Files Systems
+  - FlexParser04
+You can find instructions for working with firmware files [[https://lpcwiki.miraheze.org/wiki/Phone_and_firmware_manipulation_guide/Motorola|here]]
+==== FlashTerminal ====
+You will need Linux in order to use FlashTerminal.
+Per phone settings:
+=== M702iS ===
+  - Download FlashTerminal from [[https://github.com/EXL/FlashTerminal/tree/master|GitHub]]
+  - Under the following section <code>	if '-l' in sys.argv:
+		# Upload RAMDLD to phone and wait for RAMDLD start.
+		logging.debug('Uploading RAMDLD to phone and wa
+it for RAMDLD start.')
+		check_and_load_ezx_ap_bp_ramdlds(er, ew)</code>Uncomment the following line by removing the # at the beginning of the line<code>#		mfp_upload_binary_to_addr(er, ew, 'loaders/M702iS_RAMDLD_0303.ldr', 0x80000000, 0x80000038, True)</code>
+  - Under the following section<code>	# Dump SRAM and NOR flash.</code>Uncomment the following lines by removing the # at the beginning of each line<code>#	mfp_dump_read(er, ew, 'M702iS_ROM_Dump_1.bin', 0xA0000000, 0xA0040000, 0x200) # Skip PDS.
+#	mfp_dump_read(er, ew, 'M702iS_ROM_Dump_2.bin', 0xA0080000, 0xA2000000, 0x200) # Skip PDS.
+#	mfp_dump_read(er, ew, 'M702iS_ROM_Dump_3.bin', 0xB4000000, 0xB6000000, 0x200)</code>
+  - Execute the following command: <code>sudo ./FlashTerminal.py -l</code>